VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit capacity guide guide
starter vape kits · first-time buyers

Starter Vape Kit capacity guide guide

Buyers come to us for starter vape kit after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for first-time buyers.

Published 03 August 2026  ·  VapeWholesaleHub  ·  Reading time 5 min

Close inspection of the assembly line before the batch is released.
Close inspection of the assembly line before the batch is released.
Starter Vape Kit capacity guide guide configuration from a production run, photographed before packing.
Starter Vape Kit capacity guide guide configuration from a production run, photographed before packing.
Bulk packing station during the run for a first-time buyers order.
Bulk packing station during the run for a first-time buyers order.

Where the margin really sits

We work with first-time buyers who order between a few hundred and a few thousand units at a time, and we treat both ends the same way: a written specification, a sample you approve, and a production run that matches the sample.

Payment terms for new accounts are normally a deposit with the balance against the bill of lading. Established buyers on a repeat schedule can move to terms after three clean shipments.

A landed cost sheet for starter vape kit has five lines: unit price, packaging, freight, duty and the cost of defects. Quoting only the first line is how buyers end up surprised at the fourth.

Quality control, in plain terms

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

A 0.5 percent defect rate sounds excellent until it lands on a 600 unit order and you are handling three returns in a week. We quote realistic rates per category and we credit in advance for the known failure modes.

For first-time buyers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

How orders move from factory to shelf

Freight on starter vape kits is driven by volume more than weight. Cartons are designed to hit a clean pallet count, which is why a slightly denser pack can cut your landed cost by more than a discount on the unit price ever would.

Damage in transit is nearly always a packing decision, not bad luck. Double-walled cartons, internal dividers and a drop-tested configuration cost a little more and save the argument at the other end.

  • Reference sample retained from every batch
  • Mixed SKU cartons to spread first-order risk
  • Specification locked in writing before production starts
  • Batch codes traceable from carton back to production date
  • Document pack prepared per destination market
  • Seven-day defect reporting with replace-or-credit

Compliance without the last-minute scramble

Regulation for starter vape kits differs by country and sometimes by state. We do not pretend to be your lawyer, but we do keep the document pack current and we will tell you when a configuration cannot legally enter a market you have named.

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

Specification summary

Typical specification for this category
Battery500 mAh
Pod capacity3.0 ml
Coil resistance1.2 ohm
IncludedDevice, 2 pods, cable
ChargingUSB-C 5V/1A
PackagingBlister pack
Minimum order200 units per SKU, mixed cartons allowed
Lead time22 working days after artwork approval

The detail above is what we hold ourselves to on every shipment, including the small ones. It is also the list we will walk through with you before the first order.

Frequently asked

How long does production take?

Around 25 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

Do you support private label?

We do. Send your artwork or your brand direction and we will return a digital proof, then a physical dummy for colour approval. Packaging files stay on record so a rebrand later is a file update rather than a redesign.

What happens if part of the order is defective?

Report within seven days with photos and the batch code. Confirmed defects are replaced or credited on the next shipment. The failure is logged by mode and batch, and reviewed monthly with the factory.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us